500KG Unbraked Trailer Torsion Half Axle for Utility Trailer&Motorcycle Trailer
Price on Request
Load Capacity: 500KG
Brake Type: Unbraked
Finish:Black Paint/Galvanized
500 kg Unbraked Trailer Torsion Half Axle — OEM from China
This 500 kg unbraked trailer torsion half axle is a light-duty, rubber-damped idler half axle built for unbraked trailers up to 1000 kg gross. The housing is a welded steel tube with an internal rubber torsion arm and a forged spindle; it is designed for utility trailers, box trailers, garden trailers, micro campers and small jet-ski trailers running no braking system. Sold per side — left or right can be replaced independently after curb strike, pothole damage or bearing failure.
Key features
- Independent rubber torsion suspension. No leaf springs, no shackles, no greasable spring pivot points. The rubber cords inside the housing twist to absorb road shock.
- Unbraked idler hub. No brake drum, no brake cable, no actuator — matches trailers rated below 750 kg (EU) or built as unbraked utility units.
- One-sided replacement. Because this is a torsion half axle, you replace only the damaged side. You do not have to scrap the whole beam, which cuts repair cost and downtime.
- Two surface finishes. Black paint / powder coat for road-only use, or full hot-dip galvanizing for boat trailers, salt air and wet environments.
- OEM from a Chinese factory. Tube length, spindle type, hub PCD and mounting brackets are customizable to your drawing or sample.
Specifications
| Parameter | Typical specification |
|---|---|
| Rated load per half axle | 500 kg (1102 lb) |
| Gross rating, pair of half axles | 1000 kg (2204 lb) |
| Brake type | Unbraked idler — no drum, no cable, no actuator |
| Suspension element | Rubber torsion arm, internal rubber cords |
| Main housing | Square steel tube, fully welded |
| Spindle | Forged steel, tapered bearing seat |
| Hub bolt pattern (PCD) | 4-stub, 4×100 mm or 4×114.3 mm (customizable) |
| Wheel studs | M12×1.5 (1/2″-20 on request) |
| Surface finish | Black paint / powder coat; optional hot-dip galvanized |
| Mounting | Weld-on bracket or bolt-on hanger, per customer drawing |
| Suitable applications | Small utility trailers, box trailers, garden trailers, micro campers, jet-ski / small boat trailers |
| Country of manufacture | China — OEM factory, export packaging |
Looking for a different capacity?
We manufacture a full range of trailer torsion axles — from 350 kg light-duty half axles up to 7000 lb braked axles for US utility, cargo and boat trailers, including V-bend galvanized marine axles. Send us your drawing, sample or required load rating and we will quote the matching torsion half axle or complete axle.
FAQ
1. Can I buy just one side, or do I have to buy a complete axle?
This unit is sold as a single torsion half axle. If one side of your existing torsion axle is damaged after a bend, pothole strike or bearing seizure, you can replace only that side without replacing the whole beam. Left and right units are mirror images — please confirm the side when ordering.
2. What is the difference between a torsion half axle and a complete torsion axle?
A torsion half axle is one side only: housing tube, torsion arm, spindle and idler hub. A complete torsion axle joins two half-axle beams at a central weld or cross-member into one beam across the trailer. Two of these 500 kg half axles, mounted opposite each other, form a 1000 kg-rated unbraked complete axle.
3. Is this axle suitable for a boat or jet-ski trailer?
Yes, provided you select the hot-dip galvanized finish. The painted version is intended for road-only utility trailers. Galvanizing is the minimum we recommend for repeated fresh- or salt-water exposure; tell us your application and we will confirm the finish, bearing seal and grease spec.
4. Should I use the 500 kg figure as per-side or per-axle load?
500 kg is the rating per half axle. Two units mounted on opposite sides of a trailer give a combined 1000 kg gross axle rating. Do not exceed 1000 kg on a trailer built from two of these units, and never exceed the gross vehicle weight rating on your trailer plate.
5. Do you supply OEM / custom dimensions for trailer manufacturers?
Yes. We are a Chinese OEM factory. Tube length, spindle type, hub bolt pattern, mounting brackets and finish are all customizable from your drawing or physical sample. MOQ and lead time depend on the specification — send us your requirements and we will reply with a quote and production lead time.











